- Information
- Manuals
- Downloads
- Confirmation
- FAQ
Listing items from 1 to 20 of 47 results.
- Q.How do I set my Roland editor software to communicate with my keyboard/sound module so that I can edit sounds from the PC?
-
A.
Many Roland keyboards and sound modules come with ･･･
- Q.Can the XV series / Fantom load Performance data from the JV series and XP series ?
-
A.
The XV series / Fantom cannot load Performance data created on ･･･
- Q.Can the XV series / Fantom load Patch/Rhythm Set data of the JV series and XP series using the Bulk Dump function?
-
A.
YES. The Patch/Rhythm Set data created on ･･･
- Q.Sometimes I cannot get the pitch to bend during legato style playing on the keyboard. Could you tell me why this happens?
-
A.
The pitch of a note may not raise fully to the pitch of the ･･･
- Q.Can I use more than one multi effects at a time?
-
A.
In Performance Mode up to three multi effects are available at ･･･
- Q.What is the sampling rate and bit rate of the digital signal coming out from the digital output jack?
-
A.
XV-5080 Sampling rate; 44.1kHz / 48.0 kHz (assignable) ･･･
- Q.I would like to add the rotary speaker simulator to the distorted sound. Is it possible for me to do this?
-
A.
Since the XV Series take advantage of multiple effects ･･･
- Q.Can I use three MFXs in a serial connection in the Performance mode ?
-
A.
This is not possible. In the Performance mode, each output of ･･･
- Q.Can the Patches or Rhythm Set of the JV-1080/JV-2080 stored in the data card (M-512/M-256 etc…) be loaded to the XV series ?
-
A.
There are two following ways: Method 1: (Utilizing the ･･･
- Q.What kind of data can be loaded into the XV-5080 ?
-
A.
The XV-5080 can convert and load the following data: ･･･
- Q.The LCD screen sometimes becomes difficult to read. Why does this happen ?
-
A.
The LCD screen of the XV-3080/XV-88/XV-5080/XV-5050 is ･･･
- Q.In what situations might I find the Patch Finder useful ?
-
A.
Use the Patch Finder in the Patch Play screen (press [PATCH]), ･･･
- Q.I got a sudden change to the sound of the Patch which I registered in the FAVORITE LIST (FAVORITE SOUND). Why did this happen ?
-
A.
The Favorite List saves the Bank and Number of the Patch being ･･･
- Q.What are the differences among the output jack A(MIX), B, C, D and other output jacks ?
-
A.
In the standard setting, all the sound including the effect ･･･
- Q.I cannot get enough Chorus (Delay) or Reverb sound in the Performance mode, even though I raise the send level of the Chorus (Delay) or the Reverb considerably. Why does this happen?
-
A.
The XV series has a parameter to control the send level for ･･･
- Q.: Is it possible to set the Patch: Chorus and Reverb send levels regardless of whether or not the Multi Effect (MFX) is used ?
-
A.
The send level for the Chorus and the Reverb can be set ･･･
- Q.Does the XV series work as a GM2 sound module when receiving the "GM2 System On" MIDI message ?
-
A.
The XV series can work as a GM2 sound module when receiving ･･･
- Q.How can I set the effect individually on a specific instrument in a Rhythm Set ?
-
A.
The XV-3080/XV-88/XV-5080/XV-5050/Fantom 1. Set the Tone ･･･
- Q.Is it possible for the XV series to use two or more Rhythm Sets in the Performance mode ?
-
A.
With the XV series / Fantom any Part of the Performance can be ･･･
- Q.The sound comes out from the other side when the Panpot is set to full one side. What causes this to happen?
-
A.
Below are two conditions that may cause this problem. ･･･
- Product Support
- Link
Visit your local Roland website via the www.roland.com home page.
All content included on this website is the property of Roland Corporation. All company names, product names and logo marks mentioned in this website are registered trademarks or trademarks of Roland Corporation or their respective owners.
Copyright © 1999-2013 Roland Corporation. All Rights Reserved.