XV-5050

64-Voice Synthesizer Module

Listing items from 21 to 40 of 40 results.

<< Prev   |12|    Next >>

Q.I set up a Key Range in the Performance Mode. But sometimes the actual key range turns to be narrower than my setting. Why is this ?

A.

The Key Range setting can also be set in each Patch of your ・・・

Q.What will happen if I lose power during tone editing ? Also, what will happen to my edited patch if I select a different one?

A.

It will disappear. If you want to retain the contents of an ・・・

Q.Can I reset my User banks back to factory settings?

A.

Yes, the XV series are equipped with a Factory Reset function. ・・・

Q.Can you tell me the differences between the Performance, Patch, Rhythm, and GM Modes?

A.

The XV series incorporates four modes to achieve the best ・・・

Q.Sometimes the playback slows down (like a hiccup) and it gets out of tempo or suddenly cuts off. Why does this happen?

A.

Sometimes the playback can slow down if the sequencer or the ・・・

Q.I got noise when I have quick move to the Panpot using LFO with Matrix Control function. Could you tell me why?

A.

Slow down the speed of the move (reduce the LFO rate). ・・・

Q.Can I remotely control cutoff frequency or resonance with MIDI messages ?

A.

It is possible to remotely control cutoff frequency and ・・・

Q.Can I send a MIDI message to an XV series so that a Performance part will switch from Patch to Rhythm or vice-versa?

A.

Yes, it's possible. The XV series can switch any Performance ・・・

Q.During playback, one of my sequenced parts will not sound. I tried to select a Patch and even sent a Program Change, but still no sound comes out. Why?

A.

If the XP series receives an invalid Bank Select from a song ・・・

Q.How can I change Patches, Performances or Rhythm Kits remotely from a MIDI keyboard or sequencer ?

A.

The Patches, Performances and Rhythm Kits can be changed by ・・・

Q.Sometimes the pitch of a Patch will not go up as high as the current settings of the Pitch Bend Range for the Patch. Why does this happen ?

A.

The Pitch Bend Range of a Patch can be set from –48 to ・・・

Q.Can the XV series retain the GM Mode setting as a Performance or a Patch in Memory ?

A.

No. The GM Mode settings cannot be retained in the Memory of ・・・

Q.The settings of the Performances and Patches are changed when I turn on the power, even though I used LAST SET in the Power Up Mode in the System Parameter.

A.

When using LAST SET in the Power Up Mode, the XV series ・・・

Q.Sometimes the sound of a Patch is different from the one I edited. I wonder why this happens ?

A.

This condition can occur when you edit Volume, Modulation and ・・・

Q.Sometimes when I go back to a Performance I get a different sound from when I played it before. I wonder why this happens ?

A.

This can happen when an edit is performed on a Part or when ・・・

Q.Does the XV Series / Fantom have the same Program Change Map as the JV series/XP series ?

A.

The XV-3080 / XV-88 / XV-5080 / Fantom / XV-5050 have ・・・

Q.I installed the driver in my Macintosh, but an error massage saying "Unable to use the function extension” appeared.

A.

When the OS X driver included with your product is installed ・・・

Q.When I playback a MIDI song using an XP/XV/RS/JUNO/JV/Fantom-series instrument, only one instrument plays. Why does this happen?

A.

Most likely, Patch mode has been selected by mistake. ・・・

Q.I've connected a MIDI device to a Macintosh via USB, and am creating a setup in Free MIDI, but the connected MIDI device is not detected (or my computer freezes).

A.

It is possible that Free MIDI and other system extensions are ・・・

Q.On Mac OS X, I can't use my Roland USB MIDI device simultaneously with the E-magic amt-8 or unitor-8.

A.

You can solve this problem by installing the Unitor series ・・・

<< Prev   |12|    Next >>

To the top of page