XV-5050

Listing items from 1 to 20 of 40 results.

<< Prev   ｜1｜2｜    Next >>

Q.How do I set my Roland editor software to communicate with my keyboard/sound module so that I can edit sounds from the PC?

A.

Many Roland keyboards and sound modules come with ･･･

More

Q.Can the XV series / Fantom load Performance data from the JV series and XP series ?

A.

The XV series / Fantom cannot load Performance data created on ･･･

More

Q.Can the XV series / Fantom load Patch/Rhythm Set data of the JV series and XP series using the Bulk Dump function?

A.

YES. The Patch/Rhythm Set data created on ･･･

More

Q.Sometimes I cannot get the pitch to bend during legato style playing on the keyboard. Could you tell me why this happens?

A.

The pitch of a note may not raise fully to the pitch of the ･･･

More

Q.Can I use more than one multi effects at a time?

A.

In Performance Mode up to three multi effects are available at ･･･

More

Q.What is the sampling rate and bit rate of the digital signal coming out from the digital output jack?

A.

XV-5080 Sampling rate; 44.1kHz / 48.0 kHz (assignable) ･･･

More

Q.I would like to add the rotary speaker simulator to the distorted sound. Is it possible for me to do this?

A.

Since the XV Series take advantage of multiple effects ･･･

More

Q.Can I use three MFXs in a serial connection in the Performance mode ?

A.

This is not possible. In the Performance mode, each output of ･･･

More

Q.Can the Patches or Rhythm Set of the JV-1080/JV-2080 stored in the data card (M-512/M-256 etc…) be loaded to the XV series ?

A.

There are two following ways: Method 1: (Utilizing the ･･･

More

Q.Sometimes I hear a distorted noise which sounds like a scratch coming out from the headphone or the line out when I play several tones at a time. Can I get rid of this noise ?

A.

The XV-5050/Fantom/XV-2020 are designed so that one patch can ･･･

More

Q.What are the differences among the output jack A(MIX), B, C, D and other output jacks ?

A.

In the standard setting, all the sound including the effect ･･･

More

Q.I cannot get enough Chorus (Delay) or Reverb sound in the Performance mode, even though I raise the send level of the Chorus (Delay) or the Reverb considerably. Why does this happen?

A.

The XV series has a parameter to control the send level for ･･･

More

Q.: Is it possible to set the Patch: Chorus and Reverb send levels regardless of whether or not the Multi Effect (MFX) is used ?

A.

The send level for the Chorus and the Reverb can be set ･･･

More

Q.Does the XV series work as a GM2 sound module when receiving the "GM2 System On" MIDI message ?

A.

The XV series can work as a GM2 sound module when receiving ･･･

More

Q.How can I set the effect individually on a specific instrument in a Rhythm Set ?

A.

The XV-3080/XV-88/XV-5080/XV-5050/Fantom 1. Set the Tone ･･･

More

Q.Is it possible for the XV series to use two or more Rhythm Sets in the Performance mode ?

A.

With the XV series / Fantom any Part of the Performance can be ･･･

More

Q.The sound comes out from the other side when the Panpot is set to full one side. What causes this to happen?

A.

Below are two conditions that may cause this problem. ･･･

More

Q.Both Volume and Pan are reset when I select a new Patch in Patch Mode. Why is this?

A.

Set Patch Remain to ON so that the Control Change information ･･･

More

Q.Why does the sound get cutoff for a moment when I select a new Patch ? Is there any way to solve this problem?

A.

The XP series exchanges a vast amount of data when changing to ･･･

More

Q.When the Performance Control Channel of an XV series is set to the same MIDI channel as a Part, what will happen when they receive the same MIDI messages ?

A.

When the XV series receives a Program Change and a ･･･

More

<< Prev   ｜1｜2｜    Next >>