Digital Snake
- Information
- Manuals
- Downloads
- Confirmation
- FAQ
Listing items from 1 to 18 of 18 results.
- Q.The Cat5e Ethernet cables used for the Digital Snake have RJ45 plugs; are special high-reliability plugs available?
-
A.
Yes. The REAC ports on the Digital Snake can accept standard ･･･
- Q.What are the merits of using the S-4000 Digital Snake System to split stage audio to multiple destinations, such as a monitor console, broadcast feed, and/or multitrack recorder?
-
A.
One of the biggest advantages of using the S-4000 Digital ･･･
- Q.Can audio signals connected to the S-4000S's inputs be sent to multiple locations?
-
A.
Yes, they can. The REAC interface used in the Digital Snake ･･･
- Q.If I use switching hubs, what is the maximum distance that I can extend the Digital Snake's REAC connection?
-
A.
The maximum length for a single REAC cable is 100 meters. ･･･
- Q.What is the maximum distance that the Digital Snake system can send audio signals over a single Cat5e cable?
-
A.
Using a single Cat5e cable, the maximum transmission distance ･･･
- Q.What are the Cat5e cable requirements and precautions for REAC and the S-4000 Digital Snake System?
-
A.
About Using the REAC System The S-4000 Digital Snake System ･･･
- Q.I understand that the Digital Snake provides a redundant REAC connection in case of a cable failure. How long does it take to switch to the backup connection if the main connection fails?
-
A.
In case of an Ethernet cable failure, each REAC device ･･･
- Q.What is the recommended communication protocol for a switching hub used with the Digital Snake system?
-
A.
The S-4000 Digital Snake System uses the REAC (Roland Ethernet ･･･
- Q.How can I use a computer to control the Digital Snake system? What are the advantages of controlling it from a computer?
-
A.
The S-4000 Remote Control Software (S-4000 RCS) allows for the ･･･
- Q.Can I use the Digital Snake system without connecting the S-4000R Remote Controller?
-
A.
Yes, the Digital Snake system can be used even if the S-4000R ･･･
- Q.What is the signal transmission latency of the Digital Snake system?
-
A.
The Digital Snake system uses REAC (Roland Ethernet Audio ･･･
- Q.Can I save the S-4000S input channel settings for later recall?
-
A.
Yes, you can. Using the S-4000R Remote Controller, you can ･･･
- Q.When audio signals are transferred via the Digital Snake system, is there any degradation in audio quality?
-
A.
The Digital Snake system converts audio signals into 24-bit, ･･･
- Q.How many audio inputs and outputs are provided on the S-4000S and S-4000H?
-
A.
S-4000S 40 CH I/O Modular Rack The S-4000S provides 40 ･･･
- Q.What type of Cat5e Ethernet cable should I use with the S-4000 Digital Snake system?
-
A.
Two different types of Ethernet cables can be used with the ･･･
- Q.Does the Digital Snake's REAC interface support transmission and reception of MIDI data?
-
A.
Yes, MIDI data can be transmitted and received between REAC ･･･
- Q.Why is the Digital Snake system immune to noise?
-
A.
The Digital Snake system converts signals into digital form ･･･
- Q.After turning the power on or reconnecting a REAC cable, how long does it take until sound can be output from the Digital Snake system?
-
A.
When turning the power on: When you turn on the power of ･･･
- Product Support
- Link
Visit your local Roland website via the www.roland.com home page.
All content included on this website is the property of Roland Corporation. All company names, product names and logo marks mentioned in this website are registered trademarks or trademarks of Roland Corporation or their respective owners.
Copyright © 1999-2013 Roland Corporation. All Rights Reserved.